| 耐高温漆混合物的凸显与材料聚合物水泥基防水涂料是由合成高分子聚合物乳液(如聚丙烯酸酯、聚醋酸乙烯酯、丁橡胶乳液)及各种添加剂优化组合而成的液料和配套的粉料(由特种水泥、级配砂组成)复合而成的双组分防水涂料，一种既具有合成高分子聚合物材料弹性高、又有无机材料耐久性好的防水材料。 Polymer cement based waterproof coating is composed of synthetic high polymer emulsion (such as polyacrylate, polyvinyl acetate, butyl rubber latex) and various additives to optimize the combination of the liquid material and matching of powder (composed of special cement, graded sand) double component waterproof coating compound and into, which has elastic synthetic polymer material and inorganic material of high, good durability and waterproof material. 聚合物水泥基防水涂料主要成分：1水泥。2聚合物乳胶类(胶粉)3砂(石英砂目数)4填料(例如重钙)5助剂(消泡剂，防沉淀剂等)二、聚合物水泥基防水涂料施工工艺：一）基层条件：1清除基层表面杂物、油、砂子，凸出表面的石子、砂浆疙瘩等应清理干净， The main component of polymer cement based waterproof coating of cement: 1. 2 polymer latex (rubber) 3 sand (quartz sand mesh) 4 filler (e.g. GCC) 5 assistant (defoaming agent, anti settling agent etc.) two, polymer cement based waterproof coating construction process: a basic conditions: 1) remove grassroots surface debris, oil, sand, stone and mortar convex surface a knot in one's heart should be cleared, 清扫工作必须在施工中随时进行。2为保证涂膜牢固粘结于基层表面，要求找平层应有足够的强度，表面光滑，不起砂，不起皮。3对基层含水率无要求，基面若有明水，扫除即可施工。4阴阳角应采用水泥砂浆抹成圆弧角。二）工艺流程:基面处理—涂底胶—聚合物水泥基防水涂料配制—节点部位加强处理—大面分层涂刮聚合物水泥基防水涂料—防水层收头—组织验收。 Cleaning work must be carried out at any time during construction. 2 to ensure the coating firmly bonded on the surface of the base layer, the requirements of the leveling layer should have sufficient strength, smooth surface, not sand, not skin. 3 on the base moisture content is not required, base if have Mingshui, cleaning can be construction. 4 Yin and yang angle should use cement mortar into a circular arc angle. Two) process: surface treatment, adhesive coating, polymer cement based waterproof coating prepared - node location strengthen treatment - the surface layer coating of polymer cement based waterproof coating, waterproof layer head organization acceptance. 施工步骤:1基面处理：用铁铲、扫帚等工具清除施工垃圾，如遇渍需用溶剂清洗，基层有缺损或跑砂现象，需要新修整，阴阳角部位在找平时做成圆弧形。2涂底胶：基层平整度较差时，改性剂中掺合适量的水(一般比例为改性剂：水=14搅拌均匀后，涂抹在基层表面做底涂。 The construction steps: 1 surface treatment: removal of construction garbage with a shovel, broom and other tools, such as the case of stains by solvent cleaning, base have defects or running sand phenomenon, the need for new dressing, yin yang angle position in find usually made into arc shape. The 2 adhesive coating: base smoothness is poor when the modifier is mixed with the right amount of water (usually the proportion as the modifier: water =14 after mixing evenly, smear on the surface of the base layer as bottom coating. |
