| 耐高温漆溶剂：能溶解与稀释涂料成膜物，也可以降低涂料的粘度。但涂膜形成后并残留在涂膜中间。一种挥发性的物质t;BR>e助剂：分散剂、润湿剂、增稠剂、成膜助剂、防霉剂等。作用：提高涂料的加工性能、施工性能、贮存性能和涂膜性能的材料。 High temperature paint solvent: can dissolve and dilute paint film forming material, but also can reduce the coating viscosity. But the film formation and film residue in the middle. A volatile substance T; BR>e promoter: dispersing agent, wetting agent, thickening agent, film-forming agent, mildew inhibitor. Effect: to improve the processing performance, paint, construction performance and storage stability and the properties of coating film material. 耐高温漆成膜厚度检查；应采用针穿刺法每100平米刺三个点，用尺测量其高度，取其平均值，成膜厚度应大于2毫米。穿刺时应用彩笔做标记、以便修补。断裂延伸率检查：防水施工中，监理人员可到施工现场将搅拌好的料，分多次涂刷在平整的玻璃板上毫米， High temperature paint film thickness inspection should be every 100 square meters; Needling three points using needle puncture method, using a ruler to measure the height, the average values, the film thickness should be more than 2 mm. Puncture applied markers mark, for repair. The elongation rate of inspection: waterproof construction, supervision personnel can to the construction site, mix the material, divided into several painted on the glass plate on the flat mm, 放置7天后，1％的碱水中浸泡7天，然后在50℃土2℃烘箱中烘24小时，做哑铃型拉伸实验，要求延伸保持率达到80％施工中乳液掺加比例不足。耐水性检查：将涂料分多次涂刷在水泥块上，成膜厚度1.21.5毫米，放置7天，放入1％碱水中浸泡7天，不分层，不空鼓为合格。不透水性检查：有条件下，应用仪器检测，其方法是将涂料按比例配好， After 7 days, 7 days soak 1% alkaline water, and then in 50 C 2 C in soil drying oven for 24 hours, do dumbbell shaped tensile test, requires extending retention rate at the lack of emulsion mixing proportion in construction 80%. Water resistance: several times check will paint brushing the cement block, film thickness of 1.21.5 mm, placed for 7 days, in 7 days, 1% alkali soaking in water stratification, not hollowing qualified. Watertightness check: condition, the application of the instrument detection, the method is to paint in proportion, 分多次耐高温漆涂刷在玻璃板上天，然后放人烘箱内50℃±2℃烘24小时，取出后放置3小时，做不透水实验，不透水性为0.3MPa保持30分钟无渗漏为合格。若条件不具备，可用目测法检查防水效果，方法是将涂料分46次涂刷到无纺布上，干透后做成缓盒子形状吊空，但不得留有角， Multiple high-temperature paint coated on the glass plate of the God, then put in the oven bake 50 - 2 Deg. C for 24 hours, took place after 3 hours, do not pervious experiment, impervious to 0.3MPa maintains 30 minutes without leakage. If the conditions do not have, through visual inspection method inspection waterproof effect, method is to paint 46 times brushing to the non-woven cloth, dry made slow box shape hanging space, but shall not leave a corner, 再将1％碱水加人盒内，24h无渗漏为合格。粘结力检查：G型聚合物防水砂浆，可直接成形“8字模，24小时后出模。放人水中浸泡6天，室内温度25℃±2℃干养护21天，做粘结实验。 Then 1% alkaline plus box, 24h no leakage. Bond strength checking: G type polymer waterproof mortar, can be directly formed "8 matrix, 24 hours after the mold. People put in water for 6 days, the indoor temperature of 25 - 2 Deg. C dry curing 21 days, bond and experiment. G型耐高温漆防水砂浆，灰：水：胶=10.110.14G型防水砂浆为2.3MPa将R型涂料和成芝麻酱状，将和好的涂料涂到两个半“8字砂浆块上，放置7天做粘结实验，R型配比：胶=10.8a大于等于粘结指标为合格。 G type high temperature paint waterproof mortar, gray water glue:: =10.110.14G type waterproof mortar for 2.3MPa R type coating and tahini shape, will and good coating to 2.5 "8 word mortar block, place 7 days do bonding experiment, R type ratio: rubber =10.8a is greater than or equal to bond index for qualified. 低温柔度检查：玻璃板上打蜡，将施工现场搅拌好的涂料分多次涂刷在玻璃板上，成膜厚度1.2玻璃板上取下，放置室内条状，将冰箱温度调至箱内30分钟，用直径10毫米圆棒正反各缠绕一次，无裂纹为合格。如有裂纹说明乳液低温柔度不够。 Low temperature flexibility inspection: a glass plate wax, the construction site mixing good paint points repeatedly brushing on the glass plate, film thickness of 1.2 glass plate removed, placed indoor strip, the refrigerator temperature to the box for 30 minutes, once the wound with a diameter of 10 mm round bar of positive and negative, no crack is qualified. If there is crack that emulsion low temperature flexibility is not enough. |
